Calder and Hebble Navigation

Calder and Hebble Navigation
Looking towards the terminal basin of the Calder and Hebble Navigation, from a point near the junction with the Rochdale Canal
Specifications
Maximum boat length	57 ft 6 in (17.53 m)
Maximum boat beam	14 ft 2 in (4.32 m)
Status	Open
Navigation authority	Canal and River Trust

Calder and Hebble Navigation
River Calder and Rochdale Canal Sowerby Bridge basins Gas Works Road Weir Walker Lane Canal Road Hollas Lane Weir Calder Valley line Copley Lane Halifax Basin Halifax Branch locks (14)  A629  Exley Quay Calder Valley line  A6026  Halifax Branch 27 Salterhebble upper lock Salterhebble upper basin 26 Salterhebble middle lock Salterhebble lower basin Hebble Brook 25 Salterhebble guillotine lock  B6112  Stainland Road 24 Long Lees lock 23 Woodside Mills lock  B6114  Elland Bridge  A629  Calder Valley line 22 Elland lock 21 Park Nook lock 20 Cromwell lock Tag lock (disused) 19 Brookfoot lock Disused lock 18 Ganny lock  A643  Rastrick Bridge weir  A641  Brighouse Bridge weir Wharf Street Brighouse marina 17 Brighouse upper lock 16 Brighouse lower lock Blakeborough's Bridge To Cooper Br Anchor Pit flood lock weir  M62  15 Kirklees Top lock weir Brearly Bridge 14 Kirklees Low lock Caldervale Line Cooper Bridge flood gates  A62  Cooper Bridge Road weir -- Huddersfield Broad Canal 13 Cooper Bridge lock To Greenwood Caldervale Line Battye Cut Battyeford flood lock weir Cut Bridge (Wood Lane) Battyeford marina 12 Battyeford lock Ledgard flood lock Newgate bridge Hurst Lane bridge 11 Shepley Bridge lock Greenwood flood gates weir and access road 10 Greenwood lock Calder Road bridge Thornhill flood lock weir Savile Town Basin Dewsbury Arm 8,9 Thornhill Double locks (2) 7 Mill Bank lock Disused lock 5,6 Figure of Three locks (2) Disused lock  A642  Disused Railway 4 Broad Cut Top lock weir Railway 3 Broad Cut Low lock  M1  Thornes flood lock weir  A636  Derby Dale Road bridge 2 Thornes lock (Originally 2 chambers 1 disused) Railway bridge Wakefield flood lock weir  A61  Doncaster & Barnsley Roads  A638  Doncaster Road 1 Fall Ings lock (original lock replaced) Railway bridge  A6194  Wakefield Eastern Relief Road Railway bridge -- Aire and Calder Navigation

The Calder and Hebble Navigation is a broad inland waterway, with locks and bridge holes that are suitable for 14-foot-wide (4.3 m) boats, in West Yorkshire, England. Construction to improve the River Calder and the River Hebble began in 1759, and the initial scheme, which included 5.7 miles (9.2 km) of new cuts, was completed in 1770 and has remained navigable since it was opened. Significant improvements were made, including the Salterhebble branch to Halifax, opened in 1828, and ever-longer cuts to bypass river sections. Trade was assisted by the opening of the Rochdale Canal in 1804, which provided a through route from Sowerby Bridge to Manchester. There were plans to abandon the river sections completely in the 1830s, but these were modified as the needs of mill owners and other riparian landowners were recognised.

With the coming of the railways, the canal was leased to the Manchester and Leeds Railway in 1843, but this was subsequently deemed to be illegal, and the Aire and Calder Navigation with which the Calder and Hebble Navigation connected at its eastern end, leased the canal from September 1847 until 1885. Some of the locks were enlarged, but many were not, and having been designed for Yorkshire Keels, they remain among the shortest on the English connected waterways network, at 57 feet (17 m). The navigation became a cul-de-sac in the 20th century, but with the burgeoning interest in leisure use of the canals, the trans-Pennine Rochdale Canal was reopened in 1996 and the Huddersfield Narrow Canal followed in 2001, resulting in the navigation becoming part of three Pennine cruising rings.

History

By the beginning of the 18th century, the Aire and Calder Navigation had made the River Calder navigable as far upstream as Wakefield. The aim of the Calder and Hebble Navigation was to extend navigation west (upstream) from Wakefield to Sowerby Bridge near Halifax.

The first attempt to obtain an act of Parliament was made in 1740, as a result of a petition by the people of Halifax, Ripponden and Elland. John Eyes of Liverpool surveyed the route, and presented a scheme for a navigation which would use the River Calder from Wakefield to its junction with the River Hebble, follow the Hebble to Salterhebble bridge, and then follow the Halifax Brook to reach Halifax. It included the construction of 24 locks, 21 on the Calder and three on the Hebble, and nearly 10 miles (16 km) of cuts, including one of 2 miles (3.2 km) at Horbury. The bill was defeated, due to opposition from local landowners who feared that it would cause flooding, from millers, who thought that navigation would disrupt their water supply, and from the promoters of several Turnpike Bills, who were intending to build roads which would follow a similar route.

Calder and Hebble Navigation Act 1757
Act of Parliament
Parliament of Great Britain
Long title	An Act for extending the Navigation of the River Calder to or near to Sowerby Bridge, in the Parish of Halifax; and for making navigable the River Hebble, Halig, or Halifax Brook, from Brooksmouth to Salter Hebble Bridge, in the County of York.
Citation	31 Geo. 2. c. 72
Dates
Royal assent	9 June 1758

The second attempt followed a meeting of the Union Club in Halifax on 2 September 1756, which considered how to improve the import of wool and corn to the town. They invited the civil engineer John Smeaton to make a new survey, which he did in late 1757, and produced a scheme which involved dredging shoals, making 5.7 miles (9.2 km) of cuts, the building of 26 locks, to overcome the rise of 178 feet (54 m) between Wakefield and the Halifax Brook, and the construction of a reservoir at Salterhebble bridge. A committee raising subscriptions for the project in Rochdale insisted that the plans should be amended to include an extension to Sowerby Bridge, despite opposition from the Halifax committee. An act of Parliament, the Calder and Hebble Navigation Act 1757 (31 Geo. 2. c. 72), was obtained on 9 June 1758, for this extended route, and created commissioners, who had to own an estate valued at more than £100, or have a personal fortune of more than £3,000. Any nine of the commissioners could make decisions.

Construction

Construction started in November 1759, with Smeaton acting as engineer. By November 1764, the navigation was open as far as Brighouse, some 16 miles (26 km) from Wakefield. Having borrowed £56,000, factions arose within the commissioners, with some wanting to stop at Brooksmouth, where the Rivers Hebble and Calder meet, and others wanting to raise more money and complete the scheme. The second option gained most support, and a new committee was set up, who asked James Brindley to take over from Smeaton in 1765. The work was nearly completed by 1767, but serious floods in October caused some damage, with further damage caused by more floods in February 1768. Brindley appears to have left by mid-1766, and the Commissioners re-appointed Smeaton in 1768, to complete the work. Banks were repaired and floodgates built at the start of some of the cuts. The work was just complete when a further flood caused so much damage that the only option was to close the navigation again.

Calder and Hebble Navigation Act 1769
Act of Parliament
Parliament of Great Britain
Long title	An Act for extending the Navigation of the River Calder to Salter Hebble Bridge, and to Sower by Bridge, in the county of York, and for repealing an Act for that Purpose.
Citation	9 Geo. 3. c. 71
Dates
Royal assent	21 April 1769

By this time, £64,000 had been spent on the scheme, of which £8,100 had come from tolls and the rest had been borrowed. The Commissioners felt unable to borrow more money, and so a second act of Parliament, the Calder and Hebble Navigation Act 1769 (9 Geo. 3. c. 71), was obtained on 21 April 1769, which formally created the Company of Proprietors of the Calder and Hebble Navigation. This consisted of all of the 81 people who had loaned money to the original scheme, and these loans were converted into £100 shares. Additional shares could be issued, and the company could borrow up to £20,000, with the future tolls used as security. Before the act, the scheme had been known as the Calder Navigation or Upper Calder Navigation, and this was the first use of the Calder and Hebble title. The act was the first navigation act to include a clause which limited dividends, insisting that tolls should be reduced if the dividend exceeded ten per cent. Construction of the initial phase was finished in 1770, at a total cost of around £75,000.

There were initial problems with the water supply to the Sowerby Bridge pound, which Smeaton was asked to address. He suggested a tunnel from Hollins Mill, similar to those used for draining collieries. Construction began in June 1772, and was completed in March 1794. Other improvements followed, with a new cut between Shepley Bridge and Mirfield started in December 1775 supervised by William Jessop, and the raising of water levels in 1776 to allow boats to carry additional cargo. A new cut at Brighouse was added in 1780, while the two staircase locks at Salterhebble and the single lock at Brooksmouth were replaced at Smeaton's suggestion by three new locks in 1782.

Development

The navigation prospered, with dividends rising steadily from 5 per cent in 1771 to 13 per cent in 1792. Under the terms of the act of Parliament, tolls were reduced when the dividend exceeded 10 per cent, and the first such reduction occurred in 1791. Improvements continued, and were funded by making calls on the original shareholders. This provided a way to increase their income without exceeding the 10 per cent dividend limit. In 1798 a long cut at Thornhill was made, bypassing the town of Dewsbury. Trade with the town was maintained by the construction of a wharf and warehouse in what is now Savile Town Basin Dewsbury, however this was not until 1877. Another stimulus to trade was provided by the Rochdale Canal, which opened up a through route from Sowerby Bridge to Manchester from 1804. A new cut and a lock were constructed at Brookfoot. near Brighouse. between 1805 and 1808, while the Elland cut was extended to link up with the Sowerby cut in 1815. There were further reductions in the tolls in 1801, 1804 and 1808.

Anchor Pit Flood Gates protect the Kirklees Cut when river levels are high.

In 1806, the company agreed with the Aire and Calder Canal to replace the lock at Fall Ings with a new cut (Fall Ings Cut) and a pair of locks, the work to be jointly funded. Legal challenges from millers resulted in some delay, but the cut was opened in 1812. By 1823, as a result of pressure from carriers, boats were allowed to use the navigation at any time during the week, but the company refrained from authorising use on Sundays as they could not "consent to so great a Deviation from established Custom".

Calder and Hebble Navigation Act 1825
Act of Parliament
Parliament of the United Kingdom
Long title	An Act to enable the Company of Proprietors of the Calder and Hebble Navigation to make a navigable Cut or Canal from Salterhebble Bridge to Bailey Hall, near to the Town of Halifax, in the West Riding of the County of York; and to amend the Act relating to the said Navigation.
Citation	6 Geo. 4. c. xvii
Dates
Royal assent	31 March 1825
Other legislation
Amends	Calder and Hebble Navigation Act 1769

A new act of Parliament, the Calder and Hebble Navigation Act 1825 (6 Geo. 4. c. xvii), was obtained on 31 March 1825, which authorised the raising of £50,000 for the purpose of constructing a 1.75-mile (2.8 km) branch along the route of the River Hebble, from Salterhebble to the centre of Halifax, terminating near the railway station at Bailey Hall. The terminus was 100 feet (30 m) above the level of the canal at Salterhebble, and the branch required a total of fourteen locks. In order to avoid disputes with the mill owners along the length of the River Hebble, water supply was obtained by building a tunnel from the basin at Salterhebble to a pit near the top lock. The tunnel was 1,170 yards (1,070 m) long, and the water was pumped from the pit to the top pound by a steam engine. The branch was opened in 1828, at a cost of £58,741, of which £20,000 was raised by loans, rather than calls to the shareholders, and was abandoned in 1942.

Calder and Hebble Navigation Act 1834
Act of Parliament
Parliament of the United Kingdom
Citation	4 & 5 Will. 4. c. xii
Dates
Royal assent	22 May 1834

Calder and Hebble Navigation Act 1931
Act of Parliament
Parliament of the United Kingdom
Long title	An Act to confer further powers on the Company of Proprietors of the Calder and Hebble Navigation and for other purposes.
Citation	21 & 22 Geo. 5. c. x
Dates
Royal assent	27 March 1931

In later improvements, ever-longer cuts bypassed more and more sections of river. The mill owners prevented some of the more ambitious plans, but in many cases, the navigation company bought out the mills in order to remove the obstacles. With the Aire and Calder Canal rebuilding its main line, the Calder and Hebble sought an act of Parliament to effectively abandon the river, but this was modified, as the needs of mill owners and others who owned property on the river banks were recognised. Nevertheless, the Calder and Hebble Navigation Act 1834, when it was passed in 1834, authorised the construction of major new cuts and the building of new locks, which would be 70 by 18+1⁄2 feet (21.3 by 5.6 m) as far at Brighouse. The Huddersfield Canal pressed for the remaining locks to be extended to a similar length. A new cut between broad cut and the Figure of Three locks, which included two large locks, and a new large lock beside the old one at Thornes were opened in 1838, but little more was done, despite the Rochdale Canal pressing for longer locks.

Competition

The Manchester and Leeds Railway company, which had approached the Calder and Hebble in 1836, but had been rebuffed, opened their line between 1839 and 1841. It followed the line of the canal and that of the Rochdale Canal. A year later, with canal shares having lost 66 per cent of their value, the canal company approached the railway, who agreed to lease the canal for £40,000 per year for 14 years, commencing on 25 March 1843. The Aire and Calder Navigation objected to the lease, and in April 1847, the Attorney General and the Solicitor General ruled that it was illegal, and must cease. Soon afterwards, the Aire and Calder offered to lease the canal itself, and the agreement started in September. After the Aire and Calder's lease expired in 1885, the navigation company again took charge, rebuilt many of the bridges, and established the Calder Carrying Company. Shareholders continued to receive dividends until the canal was nationalised in 1948, and the canal was used by commercial traffic until 1981.

Current route

The Navigation starts in Wakefield, where there is an end-on junction with the Aire and Calder Navigation, and runs upstream through Mirfield, after which there is a junction with the Huddersfield Broad Canal, to arrive at Sowerby Bridge, where there is another end-on junction, this time with the Rochdale Canal. Other towns on the navigation are Horbury, Dewsbury, Brighouse, and Elland. The former branch to Halifax is no longer navigable, except for a stub now known as the Halifax Arm. A sign clearly signposts the Halifax Arm to the right, and onwards toward Sowerby Bridge, visible to boats emerging from the top lock.

Current use

Since the demise of commercial carrying in 1981, the navigation has only been used by leisure boaters, to whom it represents both an attractive cruising ground, passing through beautiful countryside and traditional Yorkshire industrial areas. For many years it was effectively a cul-de-sac, with the only access from the Aire and Calder Navigation at the eastern end. However, the growth of the restoration movement resulted in the reopening of the Rochdale Canal, to which connection was made in 1996 with the opening of Tuel Lane Lock, just beyond Sowerby Bridge, and it is now possible to reach Rochdale and Manchester. The canal always provided access to the Huddersfield Broad Canal at Cooper Bridge Junction, but this was another short cul-de-sac, until it was reconnected to the trans-Pennine Huddersfield Narrow Canal, restoration of which was completed in 2001. This links the far end of the Broad canal to Ashton-under-Lyne, and onwards to the Midlands and Wales. From the eastern end, the Aire and Calder Navigation provides links to Lancashire via Leeds and the Leeds and Liverpool Canal in the west, and to Selby, York, Goole and the Humber, Keadby and the River Trent, and Sheffield, Rotherham and Doncaster in the east. The reopening of the Rochdale and Huddersfield Narrow Canals mean that the navigation now forms part of three cruising rings, the South Pennine Ring, the North Pennine Ring and the Outer Pennine Ring.

The canal and the connected Huddersfield Broad Canal were built to accept 57-by-14-foot (17.4 by 4.3 m) Yorkshire Keels coming up the Aire and Calder Navigation. The first four locks on the lower Calder and Hebble, from Fall Ings to Broad Cut Top Lock have since been extended, and can accommodate boats which are 120 by 17+1⁄2 ft (36.6 by 5.3 m), but the remainder restrict the size of boats that can use the navigation. They are among the shortest on the connected network of English and Welsh inland waterways, but while wide beam boats are restricted to 57 feet (17 m) in length, it is possible for experienced boaters to fit narrowboats up to about 60 feet (18 m) long, but only 7 feet (2.1 m) wide, into the locks, by allowing them to sit diagonally in the restricted space. This may require expedients such as removing fenders, having shore parties pole the boat into position, and going down locks backwards. In particular, an inexperienced crew of any boat longer than about 57 ft (17 m) might find it impossible to negotiate the middle lock of the "Salterhebble Three", which is the shortest of all.

It was the disparity in boat sizes between the Calder and Hebble and the Rochdale canal which made Sowerby Bridge, at the junction of the two canals, so important, as long boats coming over from Lancashire had to have their cargoes unloaded, stored, and transferred to shorter boats at Sowerby Bridge Wharf.

A quirk of the Calder and Hebble locks is the handspike, a length of 2-by-4-inch (5 by 10 cm) timber shaped at one end to provide a comfortable two-handed grip. Calder and Hebble boaters have to carry these in addition to the more usual windlass, in order to lever open the simple lock gear which lifts the lock paddles to allow a full lock to empty or an empty one to fill. Because the navigation includes river sections, locks which give access to such sections are fitted with gauge boards, which show the condition of the river using a colour-coded scheme. A green band indicates that river levels are normal, and that navigation is therefore safe. An amber band indicates that levels are higher than normal, and that extra care is required when proceeding along the river section. A red band indicates that water levels are sufficiently high that the lock has been closed, and navigation on the river is unsafe.

Points of interest

Point	Coordinates (Links to map resources)	OS Grid Ref	Notes
Sowerby Bridge Basin	53.7098°N 1.9032°W / 53.7098; -1.9032 (Sowerby Bridge Basin)	SE064237	Jn with Rochdale Canal
top of Salterhebble Locks	53.6985°N 1.8575°W / 53.6985; -1.8575 (top of Salterhebble Locks)	SE095224	Jn with Salterhebble Branch
Park Nook Lock (No.21)	53.6957°N 1.8301°W / 53.6957; -1.8301 (Park Nook Lock (No.21))	SE113221
Brookfoot Lock (No.19)	53.7015°N 1.7976°W / 53.7015; -1.7976 (Brookfoot Lock (No.19))	SE134228
Kirklees Top Lock (No.15)	53.6924°N 1.7466°W / 53.6924; -1.7466 (Kirklees Top Lock (No.15))	SE168218
Cooper Bridge Junction	53.6831°N 1.7363°W / 53.6831; -1.7363 (Cooper Bridge Junction)	SE175207	Jn with Huddersfield Broad Canal
Shepley Bridge Lock (No.11)	53.6743°N 1.6754°W / 53.6743; -1.6754 (Shepley Bridge Lock (No.11))	SE215198
Thornhill Bottom Lock (No.8)	53.6745°N 1.6224°W / 53.6745; -1.6224 (Thornhill Bottom Lock (No.8))	SE250198	Jn with Dewsbury Arm
Figure of Three Locks (No.5,6)	53.6661°N 1.5971°W / 53.6661; -1.5971 (Figure of Three Locks (No.5,6))	SE267189
Broad Cut Low Lock (No.3)	53.6513°N 1.5340°W / 53.6513; -1.5340 (Broad Cut Low Lock (No.3))	SE308172
Thornes Lock (No.2)	53.6655°N 1.5056°W / 53.6655; -1.5056 (Thornes Lock (No.2))	SE327188
Fall Ings Lock (No.1)	53.6737°N 1.4822°W / 53.6737; -1.4822 (Fall Ings Lock (No.1))	SE343198	Jn with Aire and Calder Navigation

See also

Media related to Calder and Hebble Navigation at Wikimedia Commons

• Canals of the United Kingdom
• History of the British canal system

Bibliography

• Cumberlidge, Jane (2009). Inland Waterways of Great Britain (8th ed.). Imray Laurie Norie and Wilson. ISBN 978-1-84623-010-3.
• Hadfield, Charles (1972). The Canals of Yorkshire and North East England. Vol. 1. David and Charles. ISBN 978-0-7153-5719-4.
• McKnight, Hugh (1981). The Shell Book of the Inland Waterways. David and Charles. ISBN 978-0-7153-8239-4.
• Nicholson (2006). Nicholson Guide Vol 5: North West & the Pennines. Harper Collins Publishers. ISBN 978-0-00-721113-5.
• Priestley, Joseph (1831). "Historical Account of the Navigable Rivers, Canals and Railways of Great Britain". Archived from the original on 12 March 2016.

References

Template:Attached KML/Calder and Hebble Navigation

KML is from Wikidata

External links

Media related to Calder and Hebble Navigation at Wikimedia Commons

• images & map of mile markers seen along the Calder & Hebble Navigation